Thermal Conductivity

In: Science

Submitted By malmawaly
Words 316
Pages 2
Rules & Procedure for Term Paper (MAE 322)
Works submitted must meet the following requirements: 1. The subject of paper should be related to engineering materials. 2. At the end of this paper, I provide several topics for your term paper. You do not need any approval if you select one of these topics for your paper. However, you need approval if you want to work on a specific subject that is not included in the list. For approval, send me an email with the title of your paper. I will reply and approve or disapprove your subject. 3. The length of the paper should be 7-10 pages double spaced (12-point font), including the charts/ graphs. 4. Flow the SAE format for your paper. A copy of the format provided in BeachBoard. 5. Due Date: See the schedule in BeachBoard 6. Suggested topics: A) Adhesives B) Aluminum alloys C) Arc welding D) Case hardening E) Cast iron F) Casting G) Catholic protection H) Cements I) Cold working J) Carbon fiber Composite materials K) Glass reinforced plastics L) Reinforced concrete M) Galvanic corrosion N) Corrosion Protection O) Dye penetrant (NDI) P) Eddy current (NDI) Q) Elastomers R) Jominy and hardenability S) Polymers T) Thermoplastics U) Thermosets V) Superplasticity W) Nano materials X) Meta materials Y) Single crystal growth Z) Superconductivity [) Electrochemical Cell \) Catholic protection ]) Thermal Expansion ^) Thermal Conductivity _) Electrical Conductivity `) Magnetic Materials…...

Similar Documents

Thermal Power

...lCH1002 Energy Management in Chemical Industries Thermal Power Plants Dr. M. Subramanian Associate Professor Department of Chemical Engineering Sri Sivasubramaniya Nadar College of Engineering Kalavakkam – 603 110, Kanchipuram (Dist) Tamil Nadu, India subramanianm@ssn.edu.in 20-July-2010 Rankine cycle layout 20-July-2010 M Subramanian Rankine cycle 20-July-2010 M Subramanian Rankine cycle with reheat Power plant operation • Rankine cycle with reheat – to reduce the formation of water droplets in turbine, and to increase the efficiency of the cycle. • In order to maximize the efficiency of a steam power plant it is desirable to operate as high a temperature as possible in the super-heater. However, above about 650oC various forms of metal fatigue become significant due to very high temperatures and pressures that the walls of the boiler tubes have to withstand. • A typical 500 MW coal-fired plant consumes around 250 tonnes of coal an hour. Efficiency of Thermal Power Plant • The efficiency of a Rankine cycle is usually limited by the working fluid. Without the pressure reaching super critical levels for the working fluid, the temperature range the cycle can operate over is quite small: turbine entry temperatures are typically 565°C (the creep limit of stainless steel) and condenser temperatures are around 30°C. This gives a theoretical Carnot efficiency of about 63% compared with an actual efficiency of 42% for a modern coal-fired......

Words: 1293 - Pages: 6

Thermal Pollution

...------------------------------------------------- Thermal pollution Thermal pollution is the degradation of water quality by any process that changes ambient water temperature. A common cause of thermal pollution is the use of water as a coolant by power plants and industrial manufacturers. When water used as a coolant is returned to the natural environment at a higher temperature, the change in temperature decreases oxygen supply, and affects ecosystem composition.Urban runoff–stormwater discharged to surface waters from roads and parking lots–can also be a source of elevated water temperatures. When a power plant first opens or shuts down for repair or other causes, fish and other organisms adapted to particular temperature range can be killed by the abrupt change in water temperature known as "thermal shock." ------------------------------------------------- Ecological effects Warm water Elevated temperature typically decreases the level of dissolved oxygen of water. This can harm aquatic animals such as fish, amphibians and other aquatic organisms. Thermal pollution may also increase the metabolic rate of aquatic animals, as enzyme activity, resulting in these organisms consuming more food in a shorter time than if their environment were not changed.[4]:179 An increased metabolic rate may result in fewer resources; the more adapted organisms moving in may have an advantage over organisms that are not used to the warmer temperature. As a result, food chains of the......

Words: 786 - Pages: 4

Thermal Physics

...THERMAL PROPERTIES OF MATTER Heat is a form of energy that is transferred from a hotter to a colder region by one or more of the following methods conduction, convection and radiation. When heat is given to a body one or more of the following may happen (i) Increase in temperature (ii) Increase in length ( area, volume) (iii) Change in state of the body Solid Liquid Liquid Gas (iv) Change in chemical composition (v) Change in electrical properties (vi) Change in colour TEMPERATURE. Temperature is a measure of the Heat energy that a body contains or a measure of the Kinetic energy of the molecules of the material. By heating a material the kinetic energy of the molecules of the material also increase. The temperature also controls the direction of flow of Heat Energy. Heat Energy always flows from a higher temperature to a lower temperature. S.I. Unit of temperature is Kelvin. The Kelvin scale and the kelvin are named after the Scottish physicist and engineer William Thomson, 1st Baron Kelvin (1824–1907). Unlike the degree Fahrenheit and degree Celsius, the kelvin is not referred to as a "degree" it is written K. The Kelvin and the degree Celsius are often used together, as they have the same interval, and 0 Kelvin is -273.15 degrees Celsius. Thermometer. A thermometer is an instrument for measuring temperature. To calibrate a thermometer two temperature called FIXED POINTS are......

Words: 2312 - Pages: 10

Thermal Design

...Course Syllabus MAE 441 Fall 2013 Fall 2013 University Of Miami, School of Mechanical Engineering Instructor: Dr. S.E. Beladi, PE – Adjunct Professor DrBeladi@gmail.com ; DrBeladi@yahoo.com Time: MWF from 1:25 to 2:15 PM Office hours: MW 2:15 to 4:15 PM or by appointments Course Description: The objective of this course is to understand and design thermal Fluid systems.. The topics will includes review of thermodynamics and heat transfer, Heat Exchanger design, Convective and Conductive heat transfer rate calculations, Discussions of all types of heat exchangers, such as Double pipe, Shell and Tube, and Compact heat exchangers. Also Design of cooling towers, Solar collectors, … will be discussed. Perquisites: Thermodynamics, Dynamic, and Heat Transfer. Textbook: Heat Exchangers, Selection and rating by Sadik Kakac, and Hontan Lee, 3rd edition Reference Books: Hand book of heat exchanger design, Solar Energy Conversions Topics Covered:   |Lecture |Topic | |(Hrs, approx.) | | |5 |Review of heat transfer and thermodynamics | |6 |Classification of Heat exchangers | ...

Words: 1552 - Pages: 7

Thermal Expansion

...Thermal Expansion happens a lot in everyday life. When something is heated and expands this is Thermal Expansion. The way Thermal Expansion works, is when it is heated the atoms expand, and then when it is cooled it shrinks. Several examples of Thermal Expansi Thermal Expansion happens a lot in everyday life. When something is heated and expands this is Thermal Expansion. The way Thermal Expansion works, is when it is heated the atoms expand, and then when it is cooled it shrinks. Several examples of Thermal Expansion would be some of the following: · When mercury in a thermometer rises it is because of thermal expansion. · Thermal Expansion caused sometimes when you see cracks in concrete that have spread it. · Take a thermostat, there are two pieces of metal in a thermostat, when it gets heated up the pieces of metal spread apart and shuts the furnace off, and when it cools back down the two pieces of metal touch each other and that triggers the furnace to come back on. · Power lines can be an example of Thermal Expansion. In the summer when it is hot you will notice that the power lines hang down lower because they expand from the heat, so then in the winter you will notice they will tighten back up. · A metal roof is a good example of Thermal Expansion. When the sun hits a metal roof it will expand then when it cools down you can hear it popping and cracking because then it contracted. Those are just a few examples of Thermal Expansion, you can see this is very......

Words: 294 - Pages: 2

Thermal Conductivity

...A Study of Thermal Conductivity of Corn Cob Ash Blended Cement Mortar. A.A. Raheem, Ph.D.1* and Prof. D.A. Adesanya2 1 Civil Engineering Department, Ladoke Akintola University of Technology, Ogbomoso, Nigeria. 2 Building Department, Obafemi Awolowo University, Ile-Ife, Nigeria. E-mail: raheemayinde@yahoo.com* Telephone: 2348033928991 ABSTRACT This study investigated the thermal conductivity of corn cob ash (CCA) blended cement mortar. Nine classes of CCA blended cements were employed with the CCA content ranging from 0% to 25%. The 0% CCA replacement involved the use of normal ordinary Portland cement and it served as the control. The mix proportions of cement: sharp sand used were 1:1, 1:2, and 1:3 with water-tobinder ratio ranging between 0.26 and 0.29. Thermal conductivity test was performed using 50 x 50 x 15 mortar cube specimens cast in wooden moulds in pairs. The steady state heating method involving the use of three – blocks of brass was used for conducting the test with a heater made of nichrome wire wound round a ceramic rod. The final temperature difference obtained over a period of continuous heating for eight hours was used in determining the thermal conductivity. The thermal conductivity of CCA-blended cement specimens decreased steadily as the CCA percentage increased. For 1:1 mix proportion; the 0 thermal conductivity decreases from 1.80W/m C 0 to 0.69W/m C when the CCA percentage replacement increases from 2% to 25% as 0 against the control value of 2...

Words: 2727 - Pages: 11

Determination of Thermal Conductivity of Waste Material

...MECHANICAL ENGINEERING DETERMINATION OF THERMAL CONDUCTIVITY OF WASTE MATERIAL (PLASTICS) MECHANICAL ENGINEERING LABORATORY 2 ME 11L SUBMITTED BY: Alega, Ulysses Jr. H. Bicaldo, Mark Zedrick L. Engaño, Moises A. Sabida, Ricalyn B. SUBMITTED TO: Engr. Manuel E. Europeo March 10, 2014 INTRODUCTION Heat conduction (or thermal conduction) is the transfer of internal energy by microscopic diffusion and collisions of particles or quasi-particles within a body due to a temperature gradient. The microscopically diffusing and colliding objects include molecules, electrons, atoms, and phonons. They transfer disorganized microscopic kinetic and potential energy, which are jointly known as internal energy. Conduction can only take place within an object or material, or between two objects that are in direct or indirect contact with each other. Conduction takes place in all forms of ponderable, such as solids, liquids, gases and plasmas. Whether by conduction or by thermal radiation, heat spontaneously flows from a hotter to a colder body. In the absence of external drivers, temperature differences decay over time, and the bodies approach thermal equilibrium. In conduction, the heat flow is within and through the body itself. In contrast, in heat transfer by thermal radiation, the transfer is often between bodies, which can be spatially separate. Also possible is transfer of heat by a combination of conduction and thermal radiation. In convection, internal......

Words: 3390 - Pages: 14

Cad of Thermal Systems

...ME 416 Computer Assisted Design of Thermal Systems Actual Compressor Calculations 1. Use guidelines for ideal gas turbomachinery to calculate ideal specific work and power. 2. Calculate volume flow rate in cubic feet per minute at the compressor inlet 3. Use the Brake Horsepower for a Generic Centrifugal Compressor graph to determine the basic brake horsepower. 4. Calculate the actual power by multiplying the basic brake horsepower by the ratio of the inlet pressure (in psig) to 14.5. This will give actual power in units of horsepower. You may wish to convert it to watts. 5. Calculate the actual specific work by dividing the actual power (in W) by the mass flow rate (in kg). 6. Calculate the actual adiabatic efficiency from ηs = w ideal w act or Wideal Wact 7. Determine the actual exit conditions by first calculating the actual exit enthalpy from h out,act = h in + w act and then using property evaluation to determine the actual exit entropy and temperature. 8. Calculate any second law parameters (such as irreversibility or reversible work) that are needed. 1 ME 416 CAD of Thermal Systems Figure 1. Brake Horsepower for a Generic Centrifugal Compressor 10000 8.0 6.0 4.0 Pressure Ratio 7.0 5.0 3.5 3.0 2.5 2.0 1.5 Basic Brake Horsepower (hp) 1000 100 1 10 100 Intake Volume Flow Rate (1000 CFM) 2 ME 416 CAD of Thermal Systems Example 1: Single Stage Compressor Air at 105 kPa and 278 K enters a single stage compressor at 5 kg/s and......

Words: 770 - Pages: 4

Solar Thermal

...SOLAR THERMAL ENERGY Solar thermal is a type of technology that is used for utilizing solar energy to get thermal energy. Solar thermal energy is a form of energy in which the sun is used to produce heat that can be used in a variety of ways. This technology has been used for generations and has been constantly improved by modern technology to expand it’s applications. SOLAR THERMAL GENERATION Solar thermal energy is a renewable energy source that converts the heat from solar rays into electricity by indirect means, using steam cycles. Several types of technologies can be used to generate solar thermal energy. Different designs are used as described below; Parabolic trough designs This design uses a curved mirrored trough that reflects the solar radiation directly to a glass tube containing the fluid which runs along the length of the trough. The trough is made to tilt in an east to west direction in order to maintain direct focus of the radiation on the pipe. To reduce convective heat loss, the receiver may be enclosed in a glass vacuum chamber. This design is suitable for operation within an average temperature range from 125º C to 400º C. Power tower designs In this design, flat mirrors are used to concentrate the light on top of a tower. This method is also called the Rankine cycle and it has the advantage of achieving higher temperatures. Dish designs In this design, a solar dish is used to concentrate the sun’s rays on the heating element that is placed......

Words: 1079 - Pages: 5

Non-Thermal Effect of Microwave

...  Non-thermal E ffect of M icrowave on the Conduction C haracteristics of Na C l Solution           Shaoquan  Hou   Deli  Li  (Instructor)   Mengxiao  Li     Shanghai High School   Non-thermal E ffect of M icrowave on the Conduction C haracteristics of Na C l Solution Shaoquan Hou Deli Li(Instructor) Mengxiao Li Shanghai High School A bstract: Using the household microwave oven, we studied the effects that microwave has on the conductivity of NaCl solution. We compared the currents of NaCl solution under the microwave irradiation with the one under non-microwave irradiation under the same temperature. To our surprise, the values are different. We consider this is one of the non-thermal effects of microwave on the electrolyte solution. Further experiments indicate that the current change caused by this non-thermal effect is closely related to the concentration and temperature of the solution. Through real-time observations on the current change, we eliminated that the non-thermal effect is caused by the redistribution of the positive and negative ions. Thus the experiment results suggest that the non-thermal effect of microwave is caused by the change of the surrounding environment of the ions. K eywords : Microwave, non-thermal effect of microwave, electrolyte solution The affects the microwave has on substances or organisms which cannot be explained by thermal effect is called non-thermal effect of......

Words: 2259 - Pages: 10

Cogon Grass as Thermal Insulator

...COGON GRASS AS THERMAL INSULATING MATERIAL KRISELLE ANNE A. GERPACIO A Thesis Outline Submitted to the Department of Civil Engineering, College of Engineering and Computing, University of Southern Mindanao, Kabacan, Cotabato in Partial Fulfillment of the Requirements for the Degree of BACHELOR OF SCIENCE IN CIVIL ENGINEERING DECEMBER 2014 INTRODUCTION Significance of the Study Cogon grass known as Imperata cylindrical is considered as the one of the worst weed because it destroys the land where it grows. It deteriorates the nutrients of the soil thus creating problems to farmers. Hence, the researcher would like to study if this grass can be a substitute as thermal insulating material. If it can be an alternative, this research would really give great help to many farmers. Objectives of the Study The main objective of this study is determine whether Cogon grass can be a substitute as thermal insulator as compared to other traditional thermal insulating materials. Specifically, this study aims to: 1. determine the thermal resistance (R) of Cogon grass as thermal insulating material; 2. determine the thermal conductivity (k) of Cogon grass as thermal insulating material; 3. determine how much heat (Q) trasmit to the layer of the Cogon grass per second; and, 4. determine how much is the temperature gradient or temperature difference per unit thickness of piled Cogon grass. Scope and Limitation of the Study The study will be...

Words: 3964 - Pages: 16

Solar Thermal System for Southern Ontario

...Reflectance spectra of the TiNOX tube coating in comparison with the solar radiation and thermal infrared radiation of a black body at different surface temperatures................................................................................................................ 19 Figure 14: A glass-glass evacuated tube .................................................................... 20 Figure 15: An evacuated tube collector with covered manifold ................................... 21 Figure 16: Flat plate thermal system for water heating deployed on a flat roof .......... 21 Figure 17: Norsk Aluminum MPE absorber .................................................................23 Figure18: Norsk Aluminum multiport extruded tubes ................................................ 24 Figure 19: Fractherm Aluminum Absorber................................................................... 26 Figure 20: Volumetric Absorber ................................................................................. 26 Figure 21: A thermal network and the related cross section of a solar collector ....... 30 Figure 22: Schematic Diagram of the Solar Water Heating System ......................... 31 Figure 23: Pictures of Experimental Solar Panels (A) and the Storage System (B)....32 Figure 24: Daily Variation of the Solar Radiation Intensity (top) and Experimental and Theoretical Thermal Power of the Solar Panel (bottom) ...................................................

Words: 11958 - Pages: 48

Thermal Heat

...temperature is a measure of kinetic energy of the molecules in an object. Now the three types of heat transfer and first up is Conduction which is the transfer of energy in the form of heat by direct contact through excitement of molecules with driven by a temperature difference. Energy travels from a high to a low and the same thing happens with heat. When the high temperature molecules collide with the low temperature molecules, a transfer of energy occurs from the hot, more energetic molecules to the colder, less energetic molecules and this is recognized as conduction. Conduction is most prevalent in solids but it can also be found in liquids and gases. The rate at which heat is transmitted through a material by conduction depends on thermal conductivity which is a characteristic of a material and its mass. The easiest way to think of conduction is to hold a metal rod by one end and put the other over a fire. Eventually the hot energetic molecules from the fire will transfer to the cold, less energetic molecules of the metal rod and slowly creep up the rod to the cold end where it is being held and then move to the hand and cause burns. The second method of heat transfer is convection which is the transfer of energy through a circulating gas or liquid to or from a solid object. An example of convection is a pot on the hot stove to the water inside which then heats up the pot and the that heats up the water. Convection consists of two energy transfer......

Words: 353 - Pages: 2

Thermal Conductivity

...Abstract Our objective in this experiment was to measure the conductivity of a poor conductor, in this case, a thin piece of cardboard. By working out how much heat energy was allowed to pass from one block that had heat added to it and another block of which they were separated by a thin piece of cardboard. Our value for K, the thermal conductivity constant was 0.157 W.m-1.K-1 which was quite close to that of 0.21W.m-1.K-1 with a percentage error of 25.2%. Reference: http://www.physics.usyd.edu.au/teach_res/db/d0005e.htm Introduction & Theory The concept of conduction involves the transferring of energy through a material that can be either a poor or weak conductor, in this case, heat through a poor cardboard conductor. We expect cardboard as a poor conductor to not effectively transport heat from one disc to another, as seen in Fig. 1. Fig. 1 The formula in which we work out the value of k for the cardboard is as such: dQ/dt = -k.A.dT/dx (1) In the above equation, dQ/dt is the rate of heat transfer and is worked out using the formula (2) as below. A is the area of the cardboard disc. dT is the difference in temperature between the two discs at the steady state temperature which is explained further in the experimental method. Finally dx is the thickness of the cardboard disc. Having taken all of our measurements we will plot a graph of the temperature against the time passed as seen in Fig. 3 we then were able to get dQ/dt using the formula: ......

Words: 876 - Pages: 4

Thermal Pollution

...Temperature Thermal pollution occurs when humans change the temperature of a body of water. The most common point source of thermal pollution is cooling water, which is used to cool machinery. Thermal pollution may also be caused by stormwater runoff from warm surfaces such as streets and parking lots. Soil erosion is another cause, since it can cause cloudy conditions in a water body. Cloudy water absorbs the sun's rays, resulting in a rise in water temperature. Thermal pollution may even be caused by the removal of trees and vegetation which normally shade the water body. Thermal pollution can result in significant changes to the aquatic environment. Most aquatic organisms are adapted to survive within a specific temperature range. As temperatures increase, cold water species, such as trout and stonefly nymphs, may be replaced by warmwater species, like carp and dragonfly nymphs. Thermal pollution may also increase the extent to which fish are vulnerable to toxic compounds, parasites, and disease. If temperatures reach extremes of heat or cold, few organisms will survive. In addition to thermal pollutions' direct effects on aquatic life, there are numerous indirect effects. Thermal pollution results in lowered levels of dissolved oxygen, since cooler water can hold more oxygen than warmer water. Low dissolved oxygen levels will cause oxygen-sensitive species to die. Photosynthesis and plant growth increase with higher water temperatures, resulting in more plants. When these...

Words: 591 - Pages: 3